ISO 7175-1:2019 pdf free.Furniture – Chil dren’s cots and folding cots for domestic use -Safety requirements.
4 Safety requirements
4.1 General
With the exception of the requirements specified in 4.2, the safety requirements in Clause 4 apply both before and after testing in accordance with ISO 7175-2.
4.2 Materials
4.2.1 Materials and surfaces
All accessible parts shall meet the relevant requirements from ISO 8124-3.
4.2.2 Flammability of textiles, coated textiles and plastics coverings
When tested in accordance with ISO 8124-2:20 14, 5.4, the maximum rate spread of flame of textiles, coated textiles or plastic coverings shall be 30 mm/s.
When tested in accordance with EN 1103, there shall be no flash-effect.
4.3 Initial stability
When tested in accordance with ISO 7175-2:2019, 6.2, the cot shall not overturn.
4.4 Construction
4.4.1 General
4.4.1.1 Edges and protruding parts
Edges and protruding parts accessible during normal use shall be rounded or chamfered, and free of burrs and sharp edges.
4.4.1.2 Self-tapping screws
Self-tapping screws shall not be used to fasten any component that is designed to be removed or loosened when dismantling the cot for purposes of transportation or storage.
NOTE Self-tapping screws include wood screws, particleboard screws and the like.
4.4.1.3 Labels and decals
Glued labels and decals shall not be used on the internal surfaces of cot sides and ends unless they are below the level of the cot base or mattress base.
4.4.1.4 Smallparts
When tested in accordance with ISO 7175-2:20 19, 6.5, no accessible part that can be detached shall fit wholly within the small parts cylinder.
4.4.1.5 Castors and wheels
Castors/wheels shall not be fitted except in the following configuration, either:
a) two or more castors/wheels and at least two other support points, or,
b) at least four castors/wheels, of which at least two can be locked.
4.4.2 Holes, gaps and openings on the inside of the cot
4.4.2.1 General
With the exception of the holes, gaps and openings specified in 4.4.2.2. 4.4.2.3, 4.4.2.4. 4.4.2.5. 4.4.2.6, 4.4.4.2 and 4.4.4.3, all accessible holes, gaps and openings shall be less than 7 mm, between 12 mm and
25 mm, or between 45 mm and 65 mm when tested in accordance with Iso 7175-2:2019, 6.4.1.
4.4.2.2 Assembly holes
When tested in accordance with ISO 7175-2:2019, 6.4.1, there shall be no accessible holes between 7 mm diameter and 12 mm diameter, unless the depth is less than 10 mm.
4.4.2.3 Distance between cot base and sides and ends
When tested in accordance with Iso 7175-2:2019, 6.4.1, it shall not be possible for the 25 mm cone to pass between the cot base and the sides, and between the cot base and the ends.
4.42.4 Openings in mesh sides and ends
When tested in accordance with ISO 7175-2:2019, 6.4.1, ft shall not be possible for the 7 mm cone as described in ISO 7 175-2:2019, 5.1, to pass through the holes of the mesh.
4.4.2.5 Distance between slats of the cot base
When tested in accordance with ISO 7175-2:20 19, 6.4.1, it shall not be possible for the 60 mm cone to pass between two adjacent slats of the cot base.
4.4.2.6 Opening in mesh of the cot base
When tested in accordance with ISO 7175-2:2019, 6.4.1, it shall not be possible for the 85 mm cone to pass through a cot base made of mesh.
4.4.3 Head entrapment on the exterior of the cot
The following requirements do not apply to the cots that have a mesh or fabric sides/ends and a rigid leg or support system, when the lowest part of the opening is less than 100 mm from the floor.
When tested in accordance with Iso 7175-2:2019, 6.4.2, completely bound openings on the exterior of the cot that allow passage of the small head probe shall also allow the large head probe to pass completely through the bound opening.
Completely bound openings that allow the large probe to pass completely through shall be in accordance with the requirement for partially bound, V and irregular shaped openings when tested in accordance with ISO 7175-2:2019, 6.4.2.
Partially bound, V and irregular shaped openings shall be constructed so that:
a) portion B of the template does not enter the opening when tested in accordance with
ISO 7 175-2:2019, 6.4.2; or
b) the apex of portion A of the template contacts the base of the opening when tested in accordance with ISO 7175-2:2019, 6.4.2.ISO 7175-1 pdf download.